Troubleshooting
Ignition System
1. If a malfunction occurs in the ignition system, do not immediately assume that any particular part is causing the problem. First, check the following items:
a) Make sure that the cable clamps at the battery terminals are clean and tight.
b) Test the condition of the battery (see Steps 19 through 22). If it doesn’t pass all the tests, replace it.
c) Check the ignition coil or coil pack connections.
d) Check any relevant fuses in the engine compartment fuse and relay box (see Chassis electrical system). If they’re burned, determine the cause and repair the circuit.
Check
Warning: Because of the high voltage generated by the ignition system, use extreme care when performing a procedure involving ignition components.
Note: The ignition system components on these vehicles are difficult to diagnose. In the event of ignition system failure that you can’t diagnose, have the vehicle tested at a dealer service department or other qualified auto repair facility. Note: For the following test, you’ll need a spark tester (available at auto parts stores).
2. If the engine turns over but won’t start, verify that there is sufficient secondary ignition voltage to fire the spark plug as follows:
3. Disconnect a spark plug wire from a spark plug and install the tester between the spark plug wire boot and the spark plug (see illustration).
2.3 Here’s the setup used for checking to see if the ignition coil is sending power to the spark plug. If the coil is delivering power to the plug, the tester will flash
All models
4. Crank the engine while watching the tester. If the tester flashes, sufficient voltage is reaching the spark plug to fire it.
Caution: Do NOT crank the engine or allow it to run for more than five seconds; running the engine for more than five seconds may set a Diagnostic Trouble Code (DTC) for a cylinder misfire.
5. Repeat this test on the remaining cylinders.
6. Proceed on this basis until you have verified that there’s a good spark from each coil. If there is, then you have verified that the coils are functioning correctly.
7. If there is no spark, then either the coil is bad or the spark plug wire is bad.
8. Also inspect the coil electrical connector. Make sure that it’s clean, tight and in good condition.
9. If all the coils are firing correctly, but the engine misfires when the spark plug wires are connected to the spark plugs, then one or more of the plugs might be fouled. Remove and check the spark plugs or install new ones (see Tune-up and routine maintenance).
10. Also inspect the boots carefully for corrosion (high resistance) or deterioration of the insulation (low resistance). If any of the boots look damaged or deteriorated, replace them as a set.
11. No further testing of the ignition system is possible without special tools. If the problem persists, have the ignition system tested by a dealer service department or other qualified repair shop.
Charging system
12. If a malfunction occurs in the charging system, do not automatically assume the alternator is causing the problem. First check the following items:
a) Check the drivebelt tension and condition, as described in Chapter Tune-up and routine maintenance. Replace it if it’s worn or deteriorated.
b) Make sure the alternator mounting bolts are tight.
c) Inspect the alternator wiring harness and the connectors at the alternator and voltage regulator. They must be in good condition, tight and have no corrosion.
d) Check the fuses in the under-hood fuse/ relay box. If any are burned, determine the cause, repair the circuit and replace the fuse (the vehicle will not start and/or the accessories will not work if the main fuse is blown).
e) Start the engine and check the alternator for abnormal noises (a shrieking or squealing sound indicates a bad bearing).
f) Check the battery. Make sure it’s fully charged and in good condition (one bad cell in a battery can cause overcharging by the alternator).
g) Disconnect the battery cables (negative first, then positive). Inspect the battery posts and the cable clamps for corrosion. Clean them thoroughly if necessary (see Tune-up and routine maintenance). Reconnect the cables (positive first, negative last).
Alternator — check
13. Use a voltmeter to check the battery voltage with the engine off. It should be at least 12.6 volts (see illustration 2.19).
14. Start the engine and check the battery voltage again. It should now be approximately 13.5 to 15 volts.
15. If the voltage reading is more or less than the specified charging voltage, the voltage regulator is probably defective, which will require replacement of the alternator (the voltage regulator is not replaceable separately). Remove the alternator and have it bench tested (most auto parts stores will do this for you).
16. The charging system (battery) light on the instrument cluster lights up when the ignition key is turned to ON, but it should go out when the engine starts.
17. If the charging system light stays on after the engine has been started, there is a problem with the charging system. Before replacing the alternator, check the battery condition, alternator belt tension and electrical cable connections.
18. If replacing the alternator doesn’t restore voltage to the specified range, have the charging system tested by a dealer service department or other qualified repair shop.
Battery — check
19. Check the battery state of charge. Visually inspect the indicator eye on the top of the battery (if equipped with one); if the indicator eye is black in color, charge the battery as described in Chapter Tune-up and routine maintenance. Next perform an open circuit voltage test using a digital voltmeter. With the engine and all accessories Off, touch the negative probe of the voltmeter to the negative terminal of the battery and the positive probe to the positive terminal of the battery (see illustration). The battery voltage should be 12.6 volts or slightly above. If the battery is less than the specified voltage, charge the battery before proceeding to the next test. Do not proceed with the battery load test unless the battery charge is correct.
2.19 To test the open circuit voltage of the battery, touch the black probe of the voltmeter to the negative terminal and the red probe to the positive terminal of the battery; a fully charged battery should be at least 12.6 volts
Note: The battery’s surface charge must be removed before accurate voltage measurements can be made. Turn on the high beams for ten seconds, then turn them off and let the vehicle stand for two minutes.
20. Disconnect the negative battery cable, then the positive cable from the battery.
21. Perform a battery load test. An accurate check of the battery condition can only be performed with a load tester (see illustration). This test evaluates the ability of the battery to operate the starter and other accessories during periods of high current draw. Connect the load tester to the battery terminals. Load test the battery according to the tool manufacturer’s instructions. This tool increases the load demand (current draw) on the battery.
2.21 Connect a battery load tester to the battery and check the battery condition under load following the tool manufacturer’s instructions
22. Maintain the load on the battery for 15 seconds and observe that the battery voltage does not drop below 9.6 volts. If the battery condition is weak or defective, the tool will indicate this condition immediately.
Note: Cold temperatures will cause the minimum voltage reading to drop slightly. Follow the chart given in the manufacturer’s instructions to compensate for cold climates. Minimum load voltage for freezing temperatures (32 degrees F) should be approximately 9.1 volts.
Starting system
The starter rotates, but the engine doesn’t
23. Remove the starter (see Starter motor — removal and installation). Check the overrunning clutch and bench test the starter to make sure the drive mechanism extends fully for proper engagement with the flywheel ring gear. If it doesn’t, replace the starter.
24. Check the flywheel ring gear for missing teeth and other damage. With the ignition turned off, rotate the flywheel so you can check the entire ring gear.
The starter is noisy
25. If the solenoid is making a chattering noise, first check the battery (see Steps 21 through 24). If the battery is okay, check the cables and connections.
26. If you hear a grinding, crashing metallic sound when you turn the key to Start, check for loose starter mounting bolts. If they’re tight, remove the starter and inspect the teeth on the starter pinion gear and flywheel ring gear. Look for missing or damaged teeth.
27. If the starter sounds fine when you first turn the key to Start, but then stops rotating the engine and emits a zinging sound, the problem is probably a defective starter drive that’s not staying engaged with the ring gear. Replace the starter.
The starter rotates slowly
28. Check the battery (see Steps 19 through 22).
29. If the battery is okay, verify all connections (at the battery, the starter solenoid and motor) are clean, corrosion-free and tight. Make sure the cables aren’t frayed or damaged.
30. Check that the starter mounting bolts are tight so it grounds properly. Also check the pinion gear and flywheel ring gear for evidence of a mechanical bind (galling, deformed gear teeth or other damage).
The starter does not rotate at all
31. Check the battery (see Steps 19 through 22).
32. If the battery is okay, verify all connections (at the battery, the starter solenoid and motor) are clean, corrosion-free and tight. Make sure the cables aren’t frayed or damaged.
33. Check all of the fuses in the under-hood fuse/relay box.
34. Check that the starter mounting bolts are tight so it is grounded properly.
35. Check for voltage at the starter solenoid «S» terminal when the ignition key is turned to the start position. If voltage is present, replace the starter/solenoid assembly. If no voltage is present, the problem could be the starter relay, the Transmission Range (TR) switch (see Emissions and engine control systems), or with an electrical connector somewhere in the circuit (see the wiring diagrams). Also, on many modern vehicles, the Powertrain Control Module (PCM) and the Body Control Module (BCM) control the voltage signal to the starter solenoid; on such vehicles a special scan tool is required for diagnosis.